Fine Wire Staple (19-23 GA.) and the perfect way with the drill
The use of Fine Wire Staple (19-23 GA.) in our daily life is already very common, but when using Fine Wire Staple (19-23 GA.), for example, we make nails fixed in concrete or other hard Things above the time, will encounter nail does not go into the situation, then how do we deal with it? Maybe many people will think of drilling with a drill hole, that drill hole is how to deal with it?
We generally like the Fine Wire Staple (19-23 GA.) known as the nails, nails are mainly made of carbon steel, the biggest feature of this material is the hardness, penetration, and can not easily deform The If we encounter Fine Wire Staple (19-23 GA.) do not go into the situation, usually we will use the impact drill first make a hole, and then cut and the hole is almost a small knock into the wood, and then nail into the nail , There are ready to expand the screws do not have wood.
Here we Fine Wire Staple (19-23 GA.) manufacturers Xiaobian need to introduce a little about the drill knowledge, its main working principle is the rotation of the cutting, and the operator's thrust to carry out holes, usually mainly used in the brick Block, concrete and other objects with greater hardness, if there is steel, it is recommended to use the drill with caution.
(19-23 GA) and the combination of sawdust, we should be able to effectively separate the wood chips and Fine Wire Staple (19-23 GA.)? In the course of our day-to-day work, Today, Fine Wire Staple (19-23 GA.) manufacturers Xiaobian for everyone to do some simple introduction!
First, the fan blows.
If the wind power of the fan is large enough, the effect is also very good, but the requirements of Fine Wire Staple (19-23 GA.) weight is not too small, whether the Fine Wire Staple (19-23 GA.) also followed the run.
Second, the number of small hand picked up.
This is the best one, but the biggest performance is the lowest efficiency, you look at yourself.
Third, with a large magnet suck.
This method can also be, the use of magnets to attract nails, with a magnet sucking Fine Wire Staple (19-23 GA.), but will not take wood chips. But this approach is still a small amount of wood attached to the magnet, there is a magnet that is not everyone and the family have something to use.
Fourth, water separation method.
Fine nails (19-23 GA) and the wood into the water together, the nails in the water inside will sink, the opposite of the wood will float in the water, we only need a little Akira, you can completely separate them Open, this method is much better than the above three methods. Specifically how to operate, or to see their actual situation.
Fine Wire Staple (19-23 GA.) Optional standard:
1, professional manufacturers. The quality of the Fine Wire Staple (19-23 GA.) is extremely important in order to be effective. Therefore, it is necessary to select the products produced by the professional manufacturers. Since the demand for more than 80% of Fine Wire Staple (19-23 GA.) is concentrated on a 3.5x25 specification. So at the beginning of the selection this requires extra attention.
2, the head to round. This is also the standard for all round screws, because the production process problems, many manufacturers produce Fine Wire Staple (19-23 GA.) head may not be round, some even slightly square. The problem is that after the screw can not be completely matched with the gypsum board.
3, pointed to sharp. Especially when you are used on light steel keel. Fine Wire Staple (19-23 GA.) sharp corners generally require between 22 to 26 degrees, requiring the head sharp corners full, can not have drag silk, cracking phenomenon. This "tip" is most important for Fine Wire Staple (19-23 GA.), since the use of Fine Wire Staple (19-23 GA.) is not prefabricated and directly screwed in, so the tip also assumes Drill through the function. Especially when used in light steel keel, the bad tip will lead to drilling does not go directly affect the use. According to national standards, wall panels nail to be able to drill in 1 second through the 6mm iron plate.
- What Wire Works
- Process And Role Of Wedm Machine Tool
- Wire Used In The Environment What Are The Requi...
- How Can I Extend The Life Of Wire?
- Wire Machining Precision Is Very Important In
- Purchasing Considerations For Wire-cutting Machine
- Special Wire Guide Pulley How To Choose?
- How To Improve The Efficiency Of Wedm Machine Tool
- Wire Cutting Length For High Speed Machining Pr...
- Detailed Analysis Of The Surface Roughness Of W...
- The Industrial Value Of Staples
- C RING Maintenance Should Pay Attention To The ...
- What Is The Definition And Manufacturing Proces...
- Let's Find Out What The Next Nail Is
- Industrial Nails, Also Called Yard Nails?
- How Many Uses Of Industrial Nails Do You Know?
- Staples Is Often Problematic
- Despite The Trapped Anti-dumping, China's Fine ...
- China's Clinch Clips Processing And Development...
- What Is The Use Of Clip Nails?